domaingood

I've added a note to take a look at credit notes for the proforma task.

I think sliders that look like nodes are pretty popular, see this screenshot from vps.net - http://i34.tinypic.com/21kilia.jpg This may not be considered "Clean", unless you create a generic looking one that's easy on colors. Usually better that way anyway, because people can always tweak colors to customize.
 
Popular with VPS servers especially, as well as game servers.

This has been added for v3.3

For ticket auto-replies, do you mean the initial ticket received email? You can currently set an auto-close ticket response per department, but not the initial auto reply.
 
One thing we're planning is CORE-1358 which allows for custom email templates to be created. It may be possible then, after that, or in conjunction with that, to allow the selection of different templates in different areas of Blesta.. including auto-replies and separate templates per department.
 
So, this suggestion may fit well with that task, and be dependent on it.

if this implemented ,i think this should be per gateway , a new option in gateway about some additional fees and then he gateway should show a message to the client about this fees .
NOTE : it can be done now with a simple modification in the gateway , we have made a custom gateway for paypal named "paypal_payments_universal" that has a built-in rate exchange/curency change/showing message to cleints about the this modification .
@interfasys if you need helphow to do your own gateways with your idea , just PM me . (a votre service ... )

Here is my *very legitimate* mathematical proof:
-1 MINUS = (-1) (MINUS) = (-1)(-) = (-1)*(-) = (-)(-1) = +1

Two Factor for the Admins is there already click my info.
 
As for the customer that's coming in 3.4 under CORE-514
 
Blesta supports:
- MOTP (Mobile)
- TOTP (Time Based)
- YubiKey 
 
http://docs.blesta.com/display/user/Enabling+Two-Factor

we need more event to be implemented in blesta like :
Client Edit Profile
Client Change Password
Client Delete (Before & After action )
Client Profile Tab Fields (dropdown menu)
Contact Add | Contact Edit | Contact Delete
Client Dashboard Page Load
Client Pay Method
Client Pay Confirm
Admin Dashboard Page Load
Daily CronJob (Before & After action )
Invoice Payment Reminder
Accept Order
Delete Order
Pending Order
Order Checkout
Shopping Cart Checkout Page
Show Cart Page
Module Create (Before & After action )
Module Suspend (Before & After action )
Module unSuspend (Before & After action )
Module terminate (Before & After action )
Admin/Client Services Tab Fields (rendered)
upload Files action
Ticket Plugin :
Add - reply - close tickets
Download Manager Plugin
Download (Before & After action )
order plugin
every step event (before/after)

We would need to make some changes to allow multiple fraud detection options to be used simultaneously. It's also possible that some fraud options in the future may not play nicely together, so this is something that will need to be considered.

I've spent the last few months wiring my house, so I thought I'd share my experience and the process.
 
The Goal
My house was built in the 60's, so had no structured wiring of any kind. The telephone wires were 4 untwisted pair, which predated CAT3 by about 20 years. Lukily, just about every room in the house had a telephone drop, so I figured I could replace each drop with CAT6.
 
Thinking about it some more, since I didn't already have cable to each room I figured I might as well bundle that in as well. The goal for phase one was to add 6 drops, each with 2 CAT6 and 1 RG6. Each drop was to terminate in the coat closet due to its central location in the house. This would become my network closet.
 
The Materials
1000' CAT6 1000' RG6 quad sheild CCS (this was a mistake, more on that below) 100' RG6 dual shield pure copper 100' CAT5e 10 pack of 4-slot keystone wall plates 200 pack of CAT6 connectors and matching boots 25 pack of CAT6 keystones 8 pack of RG6 keystones 10 pack of blank keystones 10 pack of low voltage wall inserts Hinged 4U wall mount rack 24-port CAT5e patch panel 24-port CAT6 patch panel 2 desk grommets (2 3/8") 1 RG6 4-port splitter 1 RG6 8port directv splitter RG6 external enclosure Tools: Punch down tool RG6 compression tool RG6 cutter RG6 stripper Wire strippers (only needed to strip the CAT5e to connect to the telephone NID) Philips head screwdriver  
The Process
I planned the following drops:
Master bedroom Bedroom 1 Bedroom 2 Bedroom 3 Kitchen Living Room I would also neet the following utility drops:
Network closet to external enclosure for CATV and SATV utilities Network closet to Telephone NID This is what I was replacing at each drop:

 
I estimated the distance between the drop location and the network closet, then added 5 to 10 feet to ensure excess, and in some cases, avoid electrical lines in the attic.
 
I cut the RG6 and CAT6 from their spool and labeled each, then attached to the existing telephone line and climbed in the attic to pull through.

 
Lucky for me, the following was true:
In the 60's low voltage wires did not have to be stapled down. 2 CAT6 and 1 RG6 is just thin enough to fit through the 1/2" opening already drilled in the joist. Due to the sloe in the roof it would have been impossible to increase the diameter of these holes Punched down

 
Compression fitting

 
RG6 quad shield CCS was a bad choice for a couple reasons. First, Directv requires pure copper for the SWIM. That's why I had to get another 100' of RG6. Second, manipulating quad shield CCS is super difficult. That stuff is rigid. I wasn't able to pull RG6 through Bedroom 1 because that drop went down and made a 90 degree turn through a stud. The quad shield couldn't handle it.
 
While RG6 CCS is fine for video, it sucks for pulling, and has the added limitation of more resistance than pure copper. If I did this again I would have gone pure copper dual shield.
 
The finished product

 
Next I drilled two 2 and 3/8" holes to drop into the network closet. I inserted the rubberized desk grommets to prevent insulation from falling out of the ceiling, and pulled through.
 

The CAT5e is gray. I daisy chained this across the first 8 ports of the CAT5e patch panel. This allows me to patch through telephone to any one of my drops. Each telephone port supports up to 4 lines.
 

 
You can see here I'm patching the phone into my office.
 
After running the CAT5e for the telephone (and my internet). My speed changed from 7.26 Mbps / 0.92 Mbps to 7.28 Mbps / 2.20 Mbps.

Its Reseller club LB Platform.Please contact them.

I think it will be good one
 
 

There's going to be a notice staying there's 5 services pending review or something. like the Make payment alert. CORE-1228

I've assigned this to CORE-1369 as a "Task". I'm not sure this is a bug with Blesta so much as it is a bug with the domain registrar as we rely on them to do the lookup. It seems like they should be running string to lower on the input if it causes a problem.. but, this should fix it!

Hi everyone. Here I wold like to share with you how we have integrated the Blesta and Voipswitch. Client area http://demo.t-one.ca username: client password: client2013 ; admin area http://demo.t-one.ca/admin username: admin password: admin2013 You can play around create customers, register you phones and softphones, call to eachother send simple sms and so on. Actually we showed that the Blesta can do as a triple-play solution and even more.

The KB is moving up our priority list, and is tentatively scheduled for version 3.2. I don't have an ETA yet, but 3.1 is in active development and we are aiming for a beta release by the end of this month.. we'll see how it goes.

Good suggestion. I've assigned this to CORE-1360.

Centralizing human verification options to company settings has been assigned CORE-1134. Adding human verification to support tickets will depend on completion of this task.

We are planning to add some overall ticket stats like average response time, average resolution time, etc in the admin area. Do you think these averages should be displayed to the customer so they have a rough idea of when they can expect a response? If so, how and where?

I think that problem has been resolved in CORE-1354.You can wait for the next version for the fix, or add the autodebit setting with a value of 'true' to that clients' settings. I think you can simply click the link on their profile page to enable auto debit, or instead add that setting to the `client_settings` table.

Hello The community
 
 
LAST UPDATE : 23-08-2014
 
 
First i dont know if this is the correct forum to post !
 
 
another time we are happy to announce the release of the first professional Template for blesta called admin LTE , this Template is based in the adminLTE  , is bootsrap of course (3.1.x) .
 
to not talk so much i will let you with some screenshoot .
 
Login Page
 

 
 
 

 
 
Client Dashboard
 

 
 
Client Other Pages
 

 
 
when we get more time we will word in the admin side , but we need to add ability to select template for admin side like client side .
 
any BUG/SUGGESTION port it in this thread .
 
you can download it from  github https://github.com/Blesta-Addons/adminlte
 
just upload the folder adminlte inside the folder    "app/views/client/" and select the template from admin area .
 
 
THE BONUS  :
 
the color theme can be changed from admin side in look and feel , client section .
 
if you like our work , thanks or donate

What has changed since you last visited that page? You should check your error logs, or enable error_reporting in Blesta to see what error is causing the issue.

or at least make the first option selected in default .

Mine don't but maybe if you have to, I think we're expecting it to work like the packages, you know you can select a currency (convert it) as long as it's only got one currency selected for everything mate.

CORE-171 Unknown ETA.